- Bioshock remastered brightness slider not working install#
- Bioshock remastered brightness slider not working windows#
The most common causes of this issue are:
Bioshock remastered brightness slider not working windows#
If the game is directly booting up on your Deck, that would indicate either the game itself hasn't been updated at all for whatever reason, or the 2KL is being replaced with a symlink to the game executable at some point since this is a widespread problem for Windows users as well, it being skipped without workarounds seems highly improbable.Your IP address has been temporarily blocked due to a large number of HTTP requests. This is the behavior that's replicated with new prefixes, both in Experimental and GE. Any subsequent game bootups will cause the 2KL updater to appear, and then nothing.
Bioshock remastered brightness slider not working install#
The problem here is that the 2K Launcher will install and run fine. Same for the prefix nothing about the prefix setup is in any way adjusted to handle the 2K Launcher, so old and new prefixes alike will have the same issue. But again, the game itself works fine, so.
I am also not wasting the bandwidth to reinstall the game due to limited internet access as of late. Also wouldn't change anything because the game itself works fine when launching BioshockHD.exe directly, so. Here's the log after installing the 32bit library (and using a newer The game files themselves are wholly unrelated since none of it is in any way affected by the contents of the Launcher integration itself. (E: with PROTON_USE_WINED3D11=1)Įdit: I noticed I was missing lib32-vulkan-radeon after looking at the logs (not sure if it's even necessary), but installing it did not remove the crash. I'm using Ergodox EZ.Ħ.3-7 also introduces issues in color gradients. I suspect this issue hasn't come up before because very few people use a svorak keyboard (rearranged in firmware, actual x keyboard layout is set to fi for the normal qwerty Finnish layout) layout and normally these keys are on the other end of the keyboard. Interestingly though, I'm able to skip intro videos only on the newer Proton versions. These map properly to adiaeresis and odiaeresis on older Proton versions. I actually haven't tested any other key than ä and ö. Tried with both AMDVLK and Vulkan Radeon.ĥ.13-6 is the last one where input works properly. The crash happens with newer Proton versions as well. Here's what Steam logs had to say as when running the game without it: The game crashes upon launch without PROTON_USE_WINED3D11=1, and judging by previous reports it seemed mandatory. I have checked whether there are updates for my system available and I am up to date I added PROTON_LOG=1 %command% to the game's launch and got the following log: I also tried the 5.10.70 kernel instead of the 5.14.10 kernel but the issue still happens. I did a fresh install of Manjaro using EXT4 instead of BTRFS for the file system but the issue remains.
I also tried Proton GE instead of 6.3-7 but it also still remained. I have tried using XFCE instead of Mate and the issue remained. Saving and loading can also take upwards of 1 minute. The game looks like it is frozen but if I leave it will finally do it's job in the end. When I press the button to hack anything it takes usually between 30 second to 2 minutes to bring up the menu to begin the hack. So it's "fixed" thanks to a convoluted workaround, and I don't know if I'll ever be able to reproduce the original problem. HOWEVER: Confirming when this has been fixed might prove impossible, because I tried launching the game from Big Picture mode and it worked correctly, and then I tried launching it from the desktop and again it worked correctly. It's also not an issue with the game itself under Windows, my config successfully fools it into thinking I'm using an Xbox pad and it behaves accordingly.
This does not appear to be an inherent issue with Proton when I launched RAGE, the "CONFIG LOADED" popup appeared right after the Steam Overlay one and the game was controllable with the controller. When I launch the game with an Xbox 360 pad plugged in, the game recognizes it properly.
Going into the Steam Overlay and selecting STEAM CONTROLLER CONFIGURATION brings up the config I had selected. The usual "CONFIG LOADED" popup doesn't appear, and the option to turn on controller mode in the options menu is grayed out. I can't get the game to detect and let me use the Steam Controller.
0 kommentar(er)
